Yes, I fasten my Edge705 to the stem on my road, cross & mountain bikes.

It does fit the stem

The Edge 705 comes with two mounts but both are identical and will fit the bars or the stem. Just fit the zip ties Lengthways for on the bars or sideways for on the stem. I have mountings on three bikes (It's the only bike computer you need) and mounted on the stem is the best place for it.

This mount suits for the stem and the bar, respectively. This is not equal to the mounts which come with EDGE705.

Yes, it is for the handlebar stem.

The new mount has four holes. So one mount can be placed on the stem or the bar.

Yes the mount is designed to be fitted in both directions

On mine the back of the mount comes off and can be rotated 90 degrees therefore working on both bar and stem

I have my Garmin Edge 705 attached to the stem on my racing bike no problem

yes, this will fit stem and bar. The mount comes with two mounting attachments. One is wider and orientated for stem, the other is narrower and orientated for bar. I have two mounts, one on the bar of my road bike, the other one on the stem of my mtb.

No, two.

no its in two peices the rubber housing and the quick release plastic are seperate

No. You have a base, which can be fitted in two directions i.e for bar or stem plus a rubber packer as necessary. Then an interlocking mount which has to be inserted before fitting the base and securing with the two plastic ties (best to thread these ties through beforehand). When tightening the ties, ensure that the tie locks and cut ends are positioned so that they are unlikely to catch your hands. Best to leave the ties uncut for the first few rides, so that repositioning or tightening is possible, (if left uncut, you can also carefully unlock the ties using a pin or similar).

No, this is actually a 2 piece mount (adjustable dependant on where you wish to mount it on bar or stem) and comes with the wedge to alter the angle if req.

No, Its the plastic mount that sits on a rubber damper

I can only assume it is the new mount, i'm unsure if it comes from the factory with the unit or if you still have to purchase it as an after market item

Yep 2 zip ties and you are done.

for edge 705 you need option 2

option 2 - just got one and I have a 705 as well. Enjoy.

Option 2

As I understand it the mount for 500, 800, 705, 605 and 305 is the same.

Option 2 fits the 705

Option 2 (the one with zip ties) fits the 305, 605, and 705.

Option 1 with the rubber rings is for the 500 and 800.

The 500 mount is totally different to the mout for the 705/305/205. So I would have to say the one with no text.

Two sets in the box

I bought an option 2 kit and it only had one, so I assume that option 1 is the same.

You get two brackets with option one.

One set per pack

one set, but working both ways: for a stem and for a handlebar

2 sets!

Yes, option 1 works perfectly with the 310XT with the Quick Release Kit

I emailed Garmin with this very same question. Here is their response....

"The bike mount part of the quick release kit is the standard quarter turn mount.
If you already have the other components and just require to mount to another bike then the purchase of just the standard quarter turn mount would be all that is required. "

Absolutely

No.Its completely different

No its no good for the 310xt you have to buy a specific 310xt mount that doubles as a wristwatch mount / QR Strap too

yes,still one piece,just better fit.

It is the mount that can be used for handlebar or stem mounting the Garmin Edge 205/305.

Yes.

The new mount is a one piece design and much improved

Yes it is suitable

* Option 1: Edge 500 and 800
* Option 2: Edge 205, 305, 605, and 705

the edge 500 uses a different mount (see picture)

for the 500, the unit mounts by pushing it onto the mount and twisting the unit to lock it in place